Drywall Contractor Insurance by State

Texas Drywall Contractor Insurance

No statewide drywall license, city rules where the job sits, a federal certificate for disturbing older paint, an asbestos rule that names wallboard and joint compound, and workers’ compensation the employer chooses.

A worker in a cap and gray polo smooths joint compound across a ceiling with a drywall knife, looking up at the work.

Texas leaves the drywall trade without a statewide license and leaves most private employers free to decide whether to carry workers’ compensation at all. Those are the findings that shape a Texas drywall program. The rules that do bind are local and federal: the city where a job sits sets its own contractor rules, EPA certifies crews that disturb paint in older homes, and the state’s asbestos rule for public buildings names wallboard, joint compound and acoustical plaster in its own text.

Freedom from a requirement is not freedom from its consequences. An employer that goes without workers’ compensation takes on notice duties and gives up defenses, and a public owner will still ask for proof of coverage. Each section below gives the finding, the source’s own words and what an owner can do about it.

The policies themselves are explained on the drywall contractor insurance page and the coverage pages it links to. This page stays with Texas, whether your crews repair walls in occupied homes, the subject of the residential drywall contractor insurance page, or hang and finish board on general contractors’ projects, the subject of the commercial drywall contractor insurance page.

How the decision to carry workers’ compensation or go without it cascades into what a Texas drywall business owes and carries.

A cascade read from top to bottom, each step following from the step above it. It starts with the employer’s choice: apart from public employers and as the law otherwise provides, an employer may elect to obtain workers’ compensation, from a licensed insurance company or through self-insurance. An employer that goes without it must tell the state’s workers’ compensation division in writing, and must also tell each employee whether it has coverage. If a crew member is hurt and sues, the business cannot defend by saying the worker was careless, accepted the risk or was injured through a co-worker’s fault. The worker still has to prove the employer’s own negligence, or that of someone acting for it. Last, a public building contract asks for coverage anyway: the contractor certifies it for each employee on the project, and each subcontractor gives the general contractor the same certificate. No figures are shown.

Subscribe or go without: the choice the Labor Code leaves to the employer

Workers’ compensation is not compulsory for most private employers in Texas. Except for public employers and as the law otherwise provides, an employer may elect to obtain coverage, from a licensed insurance company or through self-insurance. An employer that goes without it must notify the Division of Workers’ Compensation and tell its employees, and in an injured employee’s lawsuit it cannot defend on contributory negligence, assumed risk or a fellow employee’s negligence.

Authority: Tex. Lab. Code §§ 406.002(a), 406.003, 406.004(a), 406.005(a), 406.033(a), (d), 406.096(a)–(b); Tex. Ins. Code §§ 2054.003, 2054.004

The election is written into the statute under a heading that calls coverage generally elective:

“Except for public employers and as otherwise provided by law, an employer may elect to obtain workers' compensation insurance coverage.”

The insurance regulator’s workers’ compensation division gives the employers who decline a name of their own:

“Employers that choose not to provide Texas workers’ compensation coverage to their employees are known as non-subscribers.”

For a business that does elect coverage, the statute names the routes:

“An employer may obtain workers' compensation insurance coverage through a licensed insurance company or through self-insurance as provided by this subtitle.”

No state fund stands behind those routes. The Labor Code’s coverage sections name a licensed insurance company or self-insurance, and the insurer the state created by statute to sell this coverage is, in its own statute’s words, not a state agency for any purpose.

That is the part of the finding most owners hear. The rest is what going without costs. It starts with paperwork, owed both to the state and to the crew:

“An employer who does not obtain workers' compensation insurance coverage shall notify the division in writing, in the time and as prescribed by commissioner rule, that the employer elects not to obtain coverage.”

“An employer shall notify each employee as provided by this section whether or not the employer has workers' compensation insurance coverage.”

The larger cost shows up after an injury. A worker hurt on a non-subscriber’s job can sue the employer, and the statute takes away the defenses an employer would most want to raise:

“it is not a defense that: (1) the employee was guilty of contributory negligence; (2) the employee assumed the risk of injury or death; or (3) the injury or death was caused by the negligence of a fellow employee.”

The worker still carries a burden of proof, and the statute states it:

“the plaintiff must prove negligence of the employer or of an agent or servant of the employer acting within the general scope of the agent's or servant's employment.”

Then comes the exception that reaches drywall contractors directly. One exception reaches drywall contractors directly: a government entity that signs a building or construction contract must require the contractor to certify coverage for each employee on the public project, and each subcontractor must give the same certificate to the general contractor.

As advice, treat the subscription decision as a business decision rather than a line item to cut:

  • Do you bid public work, or hang board under general contractors who do? The certificate is required on those jobs, and a private general contractor’s insurance exhibit may ask for coverage whether or not the law does.
  • If you go without, who files the notices and who tells each new hire? Put a name on each task.
  • How would an injured worker’s lawsuit be paid for, without the defenses quoted above? Settle that with your agent and your lawyer before an injury, not after.

How the policy works when you do carry it, including crews paid by the board or by the job and the certificates your own subcontractors should hand you, is set out on the workers’ compensation page.

City registration, building permits and the state license that is not there

Texas issues no statewide license or registration for drywall contractors. The regulated industries the Texas Department of Licensing and Regulation lists include air conditioning and refrigeration contractors, electricians and water well drillers, and no general, building, drywall or plastering contractor; the chapter headings of the Texas Occupations Code name no drywall, plaster or general contractor trade either. Texas law leaves contractor rules to local government instead: a city may adopt ordinances for its good government and for its trade and commerce.

Authority: Tex. Loc. Gov’t Code § 51.001

The local power comes from the Local Government Code, which lets a city govern trade within its limits:

“The governing body of a municipality may adopt, publish, amend, or repeal an ordinance, rule, or police regulation that: (1) is for the good government, peace, or order of the municipality or for the trade and commerce of the municipality”

No state license is not the same as nothing being required. A city can set its own rules for the contractors who work inside it — Fort Worth, for one, requires any business that obtains a permit under the building provisions of its codes to keep a contractor registration on file — so the rule for a particular job comes from the city where the work is done.

The City of Fort Worth is the example the record verified: the city requires a contractor registration on file for any business that obtains a permit under the building, mechanical, plumbing or electrical provisions of its codes; the page does not name drywall as a separate trade. In the city’s own words:

“Any firm, business, individual or organization obtaining a permit related to the building, mechanical, plumbing or electrical provisions of the City of Fort Worth's Codes shall have on file in the Development Services Department a valid Contractor Registration”

Read that rule for what it covers. It keys on the permit, not the trade, so whether a drywall subcontractor must register turns on who pulls the permit and on what the city decides, and only the city can answer that. Other cities set their own rules, and no statewide list gathers them.

As advice, before you bid in a city new to you, ask its development or building office whether it registers contractors and whether a subcontractor working under someone else’s permit is included. Keep a page for each city with what it issued you and when anything lapses, and do not assume a rule from your home city carries over to the next city down the highway.

The certificates and additional insured wording a general contractor asks for before work starts are taken up on the commercial drywall contractor insurance page.

Older paint on the wall: a federal renovator rule beside a state abatement program

Texas is not an authorized RRP state: the U.S. Environmental Protection Agency administers the lead renovation, repair and painting (RRP) program there, so the lead-safe certification a drywall firm needs for paid work that disturbs paint in older homes and child-occupied facilities comes from EPA.

Authority: 40 CFR Part 745; 25 TAC Chapter 295, Subchapter I

Cutting out a damaged section, opening a wall for a new doorway or sanding a patch flush disturbs the paint on that wall. The federal rule is written around that kind of paid work:

“In general, anyone paid to perform work that disturbs paint in housing and child-occupied facilities built before 1978 must be certified in lead-safe work practices.”

The state health department’s own summary sets out who runs what in Texas:

“In Texas, the U.S. Environmental Protection Agency (EPA) is administering the Renovation, Repair, and Painting (RRP) Program Rule while the Texas Department of State Health Services (DSHS) is administering the program for lead inspections, lead risk assessments, and lead abatements”

The Texas Department of State Health Services runs the state’s own Environmental Lead Program under the Texas Environmental Lead Reduction Rules, which certify the individuals and firms that do lead inspections, risk assessments and abatement, not renovation. Cutting out or sanding painted walls in an older home is renovation work under the federal rule; lead abatement work is what needs the state’s certification.

“the individuals and firms conducting this work must be certified (licensed) by the Texas Department of State Health Services (DSHS), Environmental Lead Program.”

As advice, settle the lead question on the estimate, not on the job. Ask when the building went up and whether it is a home or a child-occupied facility, write down how much painted surface the crew will cut or sand, and confirm which certified renovator will be on site. Lead abatement is a different line of work with its own state certification; if a job turns into abatement, it is not a drywall scope any longer.

How a liability policy treats a claim that involves lead or another contaminant is worked through on the general liability page, and older homes get their own attention on the residential drywall contractor insurance page.

Wallboard, joint compound and acoustical plaster in the asbestos rule’s text

Texas’s asbestos rule, the Texas Asbestos Health Protection Rules run by the Department of State Health Services, reaches drywall work in public buildings and names drywall materials in its own text: it counts repairs to a piece of asbestos-containing wallboard among small-scale, short-duration activities, defines surfacing material to include acoustical plaster, and lists joint compound and wallboard among the materials an installer in a public building must first check against a safety data sheet. Before renovation, a public building’s owner must have an asbestos survey performed, and the Occupations Code bars unlicensed renovation that disturbs asbestos in a public building. The rule does not apply to a single private residence or a small apartment building.

Authority: 25 TAC §§ 296.1, 296.21, 296.191; Tex. Occ. Code § 1954.101; 40 CFR 61, Subpart M

This rule speaks a drywall crew’s language directly. Start with what it reaches:

“This chapter applies to a person disturbing, removing, encapsulating, or enclosing any amount of asbestos within a public building for any purpose, including repair, renovation, dismantling, demolition, installation, or maintenance operations”

Repair is in that list, and the rule’s definitions show it had wall repair in mind. Among the small-scale, short-duration activities it defines is this:

“repairs to a piece of asbestos-containing wallboard”

The rule’s definition of surfacing material uses a finisher’s material as its example:

“Material that is sprayed on, troweled on, or otherwise applied to surfaces, such as acoustical plaster on ceilings and fireproofing materials on structural members, or other materials on surfaces for acoustical, fireproofing, or other purposes.”

The rule also looks forward, to the material going up. Before new building materials are installed in a public building, it asks for the safety data sheet, and its list includes the materials a drywall crew handles every day:

“A person must obtain an MSDS or SDS before installing the following building materials or replacement parts: (A) surfacing materials: (i) acoustical plaster; … (vii) joint compound”

“(C) miscellaneous material: … (xxvi) wallboard”

The survey comes before the work, and the rule places it on the owner:

“Before any renovation or dismantling outside of or within a public building, commercial building, or facility, including preparations for partial or complete demolition, the owner must have an asbestos survey performed.”

The statute the rule implements makes the license a condition of the work itself:

“Unless a person is licensed under this chapter, the person may not: … perform or supervise maintenance, repair, installation, renovation, or cleaning that dislodges, breaks, cuts, abrades, or impinges on asbestos materials in a public building”

Homes sit outside the rule. Its scope section says so directly, with an exception for residential buildings the federal emission standard reaches:

“This chapter does not apply to a single private residence or a single apartment building with no more than four dwelling units, except for a residential building subject to NESHAP”

The Texas Department of State Health Services Asbestos Program puts the licensing point plainly in its general answers. This is the department’s guidance, not the rule:

“People and companies that work with asbestos in Texas public buildings must have a license or registration from the Texas Department of State Health Services (DSHS).”

As advice, for any job in a school, office, store or other public or commercial building:

  • Ask the owner or general contractor for the asbestos survey before you price demolition or repair.
  • Keep the safety data sheets for the compound, board and plaster you install on public-building jobs in the job file.
  • If regulated material has to be disturbed and your business is not licensed for it, schedule a licensed firm to do that part before your crew starts.
  • In homes, do not read the exclusion as a clean bill. Have older texture tested before the crew scrapes it.

Whether a liability policy answers a claim involving asbestos is taken up on the general liability page.

Which office handles which question

The Texas Department of Insurance regulates insurance in the state. You can look up an insurance agency’s license, ours included, on NIPR.com.

The other bodies behind this page, each linked to its own site and described as the record verified it:

Missing from that list on purpose: a statewide contractor board for drywall work and a state workers’ compensation fund, neither of which exists. For licensing, the office that matters on a given job is the city’s.

Big metros, many city halls: the counties behind each market

Ranked by the U.S. Census Bureau’s population estimates, these are the largest metropolitan areas with a principal city in Texas. Because contractor rules come from cities, a crew working across any of them can meet a different rule at each stop.

Dallas-Fort Worth-Arlington, TX

Texas counties this metro takes in: Collin County, Dallas County, Denton County, Ellis County, Hunt County, Johnson County, Kaufman County, Parker County, Rockwall County, Tarrant County and Wise County.

Houston-Pasadena-The Woodlands, TX

Texas counties this metro takes in: Austin County, Brazoria County, Chambers County, Fort Bend County, Galveston County, Harris County, Liberty County, Montgomery County, San Jacinto County and Waller County.

San Antonio-New Braunfels, TX

Texas counties this metro takes in: Atascosa County, Bandera County, Bexar County, Comal County, Guadalupe County, Kendall County, Medina County and Wilson County.

Austin-Round Rock-San Marcos, TX

Texas counties this metro takes in: Bastrop County, Caldwell County, Hays County, Travis County and Williamson County.

McAllen-Edinburg-Mission, TX

Texas counties this metro takes in: Hidalgo County.

El Paso, TX

Texas counties this metro takes in: El Paso County and Hudspeth County.

As advice, plan a metro as a collection of cities rather than a single market: note the city and county of each job, and check that city’s rule before the bid goes out.

The policies that pick up where the Texas rules stop

The rules above describe Texas. The coverage that answers for the work is the same set of policies a drywall business carries anywhere, each with its own page:

Bring the workers’ compensation decision to the quote request, along with the cities and the kinds of buildings you work in.

Texas: what the state sets for drywall work, what each rule leaves open, and the coverage page that discusses it.
Contractor license No statewide license; a city, town or county may set its own
Injury and damage to others from the work, during the job and after it General Liability
Lead-safe renovation The federal program runs lead-safe renovation here
Paint dust disturbed when older walls are cut, patched or sanded General Liability
Asbestos in wall and ceiling material A state program reaches removal of this material
Disturbing older joint compound, wallboard or plaster General Liability
Workers’ compensation Not required of every employer
A crew member hurt on the job Workers’ Compensation

State rules decide who may do the work and how; the policies decide who pays when something goes wrong.

  • A license, registration or certification is a requirement of the state, not insurance.

A panel for Texas in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. Contractor license: No statewide license; a city, town or county may set its own. It leaves open injury and damage to others from the work, during the job and after it, which General Liability answers. Lead-safe renovation: The federal program runs lead-safe renovation here. It leaves open paint dust disturbed when older walls are cut, patched or sanded, which General Liability answers. Asbestos in wall and ceiling material: A state program reaches removal of this material. It leaves open disturbing older joint compound, wallboard or plaster, which General Liability answers. Workers’ compensation: Not required of every employer. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.

Nearby states we also write

Texas drywall contractor insurance questions

Does the state make us register before my crew hangs board for a builder in a Texas city?

Not from the state. The Texas Department of Licensing and Regulation regulates a list of industries that holds no general, building, drywall or plastering contractor license. Contractor rules are set by cities instead; the City of Fort Worth, for example, requires a contractor registration on file from any business that obtains a permit under the building provisions of its codes, though its page does not name drywall. Ask the city where the job sits before the bid goes out.

We stopped carrying workers’ compensation. What do we have to do now that we are without it?

The Labor Code asks for notice to the state and to the crew. The business must notify the Texas Department of Insurance, Division of Workers’ Compensation in writing that it elects not to obtain coverage, in the time and manner the commissioner’s rule prescribes, and it must tell each employee whether or not it has coverage. Keep copies of both notices with your payroll records.

A taper on our crew got hurt and is suing us. Can we argue he was careless or knew the risk?

Not if the business went without workers’ compensation. In an injured employee’s action against an employer without coverage, the Labor Code says it is not a defense that the employee was contributorily negligent, assumed the risk or was hurt through a fellow employee’s negligence. The employee must still prove negligence by the employer or by someone acting for it within the job. Talk to a lawyer the day a suit arrives.

The school district wants a coverage certificate before we start. Why would a public owner ask for that?

Because the Labor Code requires it. A governmental entity that enters into a building or construction contract must require the contractor to certify in writing that it provides workers’ compensation coverage for each of its employees on the public project, and each subcontractor must give the same kind of certificate to the general contractor. If you are a drywall subcontractor there, the certificate goes to the general contractor.

An older home we are repairing still has its original painted walls. What paperwork does our crew need before cutting into them?

A lead-safe renovation certificate, which comes from EPA. Texas does not run its own renovation program; the Texas Department of State Health Services Environmental Lead Program certifies the people and firms who do lead inspections, risk assessments and abatement, not renovation. Cutting or sanding painted walls in an older home is renovation work under the federal rule, so the state’s abatement certification is not the one your crew needs.

We have a patch-and-repair job on wallboard in a county office building. What has to happen before we cut in?

The state asbestos rule can reach it. The rule applies to anyone disturbing any amount of asbestos in a public building for repair, renovation or maintenance, and it lists repairs to a piece of asbestos-containing wallboard among its small-scale, short-duration activities. The building owner must have an asbestos survey done before the work, and renovation work that disturbs asbestos in a public building takes a license from the Texas Department of State Health Services. Ask for the survey before you price the job.

A homeowner wants an old textured ceiling scraped off. What does the state asbestos rule say about houses?

That it generally stays out of them. The rule does not apply to a single private residence or a small apartment building, except for a residential building that the federal asbestos emission standard reaches. That exclusion says nothing about what the ceiling contains, so as advice, have older texture tested before your crew scrapes it.

This page describes insurance for drywall contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, lead-safe and asbestos requirements change; verify current requirements with the agency named before relying on them.

Get a quote for your Texas drywall work

Send us the cities your crews work in, any public buildings on the schedule and whether you carry workers’ compensation today, and we will shape the program from there.