Drywall Contractor Insurance by State
Maine Drywall Contractor Insurance
Maine licenses no drywall trade, yet a home construction contract law, a federal lead rule, an asbestos rule that names joint compound and a compulsory comp law all reach the work.
Maine’s asbestos rule names joint compound in its own words and draws a line through it: compound that only filled nail holes and taped seams is outside the rule when it comes off, while compound laid on as a layered coat is not exempt. Around that finding, the state licenses no drywall or general contractor, a home construction contract law sets the paperwork for residential jobs, lead-safe certification comes from EPA with a state duty to contain paint debris beside it, and workers’ compensation is compulsory for every private employer, met through a policy or self-insurance because there is no state fund.
Each finding below is given as it was verified, in the source’s own words where they carry the point. How the policies themselves respond is set out on the drywall contractor insurance page; this page keeps to what is particular to Maine, whether your crews refinish rooms in occupied houses, the subject of the residential drywall contractor insurance page, or hang and finish board on larger projects, which the commercial drywall contractor insurance page takes up.
A hub with spokes. At the center is joint compound on an older wall or ceiling in Maine. A spoke labeled removal sits outside the rule runs to compound that only filled nail holes and taped seams, whose removal the rule lists among the activities it does not reach. A spoke labeled not exempt runs to compound laid on as a layered coat over walls and ceilings, which stays inside the rule. A spoke labeled no sampling needed runs to gypsum board whose compound was a filler only, which the rule lists among materials that need no inspection, sampling or analysis. A spoke labeled who handles regulated work runs to licensed firms and certified workers, who do abatement inside the rule, with notice to the state environmental department. A spoke labeled checked before the walls open runs to an inspection the owner or operator has done before a renovation that impacts wall or ceiling systems. A spoke labeled skips the inspection, not the license runs to single-family homes, which the rule exempts from its inspection provisions while the statute’s licensing duty is not limited by building type. No figures are shown.
Joint compound by name: taped seams out, layered coats in
Maine’s asbestos rule, Chapter 425 of the Department of Environmental Protection’s rules, names joint compound in its own words. It leaves out of the rule the removal of joint compound used only to fill nail holes and tape seams, but says joint compound used as a layered system on walls and ceilings is not exempt; asbestos abatement work otherwise must be done by licensed businesses and certified professionals, with notice to the department. Before a renovation that impacts wall or ceiling systems, the owner or operator must have an asbestos inspection done, and the rule exempts single-family homes from that inspection.
Authority: 06-096 CMR ch. 425, §§ 2(D), 2(F)(5), 6(A); 38 M.R.S. §§ 1272, 1273; 40 CFR 61, Subpart M
Start with the prohibition, because everything else in the rule is measured against it:
“No person or owner or operator may engage in, or arrange for, any asbestos abatement activities in Maine unless the asbestos abatement activity is performed by licensed entities and certified professionals …”
The statute behind the rule states the same duty, and it does not limit that duty to any kind of building:
“No person or owner or operator may engage in any asbestos abatement activities in the State, unless licensed or certified pursuant to this chapter”
Now the part that names the finisher’s own material. Among the activities the rule says it does not reach is the removal of compound used for the most ordinary purpose in the trade:
“The removal and containerization of asbestos-containing joint compound used to fill nail holes and tape seams in building component systems including but not limited to walls and ceilings.”
Read alone, that line sounds like a broad pass for drywall work. It is not, because the note the rule attaches to the same item closes the door on the other way compound goes on a wall:
“Joint compound used as a layered system on walls, ceilings, etc., is not exempt.”
Those lines belong together. Compound spotted over fasteners and run along tape is one thing; compound troweled across a whole surface in coats is another, and the second stays inside the rule. The same split runs through the rule’s inspection section, which lets gypsum board skip inspection only on this condition:
“gypsum board when joint compound was used only as a filler and not as a layered component”
For an owner, the practical reading is this. A crew cutting out a patch around a few taped seams and a crew sanding down a ceiling skim-coated edge to edge are not doing the same thing under this rule, even with the same tools in hand. As advice:
- Before you price a tear-out or heavy sanding on an older finish, find out whether the compound is a filler or a layered coat, and whether anyone has tested it.
- Write the method into the proposal: which surfaces are cut, which are sanded, which come down whole.
- If regulated material has to come out and your firm does not hold the state license, schedule a licensed abatement contractor first and bring your crew in after.
An inspection before the wall comes down, and the homes it skips
The rule puts a step in front of renovation work that touches the systems a drywall crew works on. It opens by naming them,
“Prior to conducting a renovation or demolition activity that impacts any building material likely to contain asbestos (such as those used in roofing, flooring, siding, ceiling, and wall systems) …”
and says whose job the inspection is:
“the owner or operator must have an inspection conducted for the presence of asbestos-containing materials.”
The duty sits with the owner or operator, not the drywall subcontractor, but the crew is the one standing in the dust when an inspection was skipped. The rule also carries a residential exemption:
“Single family residences, and residences constructed after 1980 that consist of two (2) to four (4) units, are exempt from the inspection provisions of this section.”
Read the last words carefully. The exemption is from the inspection provisions of that section. It does not take a house out of the licensing duty quoted above, and it says nothing about whether the finish in a given house contains asbestos.
The Maine Department of Environmental Protection asbestos program adds its own reading. That is the department’s guidance, not the text of the rule. Once a decision is made to disturb the material, it says,
“it must be removed or repaired by professionals unless specifically exempted from the DEP regulations.”
On renovations, its inspection page states the order of work, and it speaks to homeowners directly:
“Similarly, if any ACM is identified or assumed in areas of a building that will undergo renovation, the ACM must be removed by a DEP-licensed Asbestos Abatement Contractor before the renovation occurs.”
“Homeowners are responsible for any disturbance of ACM in amounts greater than 3 square or 3 linear feet.”
A homeowner responsible for a disturbance is the person who hired your crew to make it, so the conversation about testing belongs at the estimate. As advice, on a commercial or multi-unit renovation ask for the inspection report before you price the work, and on a house, ask whether anyone has tested the finishes you will open. How a liability policy treats a claim involving asbestos is taken up on the general liability page.
A trade the state leaves unlicensed, and the contract law that still reaches it
Hanging and finishing drywall in Maine needs no state contractor license or registration. The Office of the Maine Attorney General says general contractors and trades such as roofing and framing are not licensed or regulated in Maine; the trades the state does license, plumbing and electrical work, do not reach wallboard, taping or plaster.
No license does not mean no rules. Maine’s home construction contract law reaches residential remodeling and repair, including nonstructural work, and requires a signed written contract above a set amount, and larger municipalities must enforce the state building code, so the town where the job sits is where to ask about permits.
Authority: 10 M.R.S. §§ 1486, 1487, 1490
The Office of the Maine Attorney General puts the licensing finding in a single sentence, and names the building trades the state does license:
“In Maine, general contractors - and trades such as roofing and framing - are not licensed or regulated.”
“The State of Maine licenses plumbers and electricians, who are subject to disciplinary action by their licensing board if they violate Maine law or the board’s rules.”
No license is not the same as no law. The home construction contract statute reaches drywall work on a house through its definition of the contracts it covers:
“means a contract to build, remodel or repair a residence, including not only structural work but also electrical, plumbing and heating work; carpeting; window replacements; and other nonstructural work.”
A residence, for the same chapter, is a small dwelling, and commercial buildings sit outside it:
“means a dwelling with 3 or fewer living units and garages, if any. Buildings used for commercial or business purposes are not subject to this chapter.”
Inside that reach, a job above the amount the statute names must be in writing and signed by both sides, and a breach of the chapter counts as evidence of an unfair trade practice:
“Any home construction contract for more than $3,000 in materials or labor must be in writing and must be signed by both the home construction contractor and the homeowner or lessee.”
“Any violation of this chapter shall constitute prima facie evidence of a violation of the Unfair Trade Practices Act”
The building code is the other piece the state leaves to towns, and the Attorney General’s page says which municipalities must enforce it:
“Any municipality that has more than 4,000 residents must enforce the Maine Uniform Building and Energy Code”
As advice, use a written contract on every residential job, signed before work starts, so a small job that grows is already covered. Ask the town office about permits and inspections while you are still bidding; only the town can say how it handles the code. On a commercial job the home construction statute is not your paperwork: the contract with the owner or general contractor is, and the proof of insurance it asks for is taken up on the commercial drywall contractor insurance page.
Federal lead certification, and the cleanup duty written into state law
Maine is not an authorized state for EPA’s lead renovation, repair and painting (RRP) program, so the lead-safe certification a drywall firm needs for paid work that disturbs paint in older homes and child-occupied facilities comes from EPA. The Maine Department of Environmental Protection runs the state’s lead program, which licenses lead inspection and abatement.
Authority: 40 CFR Part 745; 38 M.R.S. § 1296
Drywall work meets old paint every time a crew cuts out a damaged section or sands a patch flush with the surrounding finish. The federal rule is written around that kind of paid work, and the state’s own lead page points contractors to it:
“In general, anyone paid to perform work that disturbs paint in housing and child-occupied facilities built before 1978 must be certified in lead-safe work practices.”
“Federal Renovation, Repair and Painting Rule - New federal rule requires contractors to do lead-safe renovations in homes and day cares built before 1978.”
That does not leave the state silent. The Maine Department of Environmental Protection runs the state’s lead program, and its page says who may identify a lead hazard:
“By law, lead hazards may only be identified by a Maine-licensed lead inspector or risk assessor in the course of a lead inspection.”
Outside abatement, a Maine statute reaches every renovation, remodeling, maintenance or repair project involving lead-based paint that falls outside the state’s licensing: the person doing it must take reasonable precautions to keep lead out of the environment, including cleaning up and disposing of the paint debris.
“A person engaged in any renovation, remodeling, maintenance or repair project involving lead-based paint not subject to the licensing and certification requirements of this chapter shall take reasonable precautions to prevent the release of lead to the environment”
The useful split for an owner: the renovation certification is federal, finding lead hazards is a job for a state-licensed inspector or risk assessor, and the precautions statute asks every renovation crew outside the licensed work to keep lead out of the environment and clean up after itself. As advice, put the building’s age, the painted surface the crew will disturb and the name of your certified renovator on the estimate sheet, and plan the debris cleanup as part of the job rather than the last afternoon. How a liability policy treats a lead claim is worked through on the general liability page.
A payroll of any size, and the insurer the statute keeps open for comp
Workers’ compensation is compulsory in Maine: every private employer, including an independent contractor who hires and pays employees, must secure compensation for all employees by buying a workers’ compensation policy or by self-insuring. There is no state fund. A company created by statute as a mutual insurer must cover employers who cannot or do not buy coverage elsewhere in the voluntary market, and it is a private carrier, not a state agency.
A drywall business with even one employee is inside the law; a sole proprietor with no employees is not required to carry the coverage.
Authority: 39-A M.R.S. §§ 401(1), 403(1); 24-A M.R.S. §§ 3703, 3705, 3711(1)
The statute names the independent contractor with a payroll in the same breath as every other employer, and the route most drywall businesses take is the first it lists, an insurance policy:
“Every private employer, including an independent contractor who hires and pays employees, is subject to this Act and shall secure the payment of compensation with respect to all employees by purchasing a workers' compensation policy or self-insuring”
“The employer may comply with this section by insuring and keeping insured the payment of such compensation and other benefits under a workers' compensation insurance policy.”
The Bureau of Insurance answers the question small owners ask most in its employer guide:
“A sole proprietor with employees is required to carry workers’ compensation for those employees.”
There is no state fund to buy from. What the statute does provide is a company, created as a mutual insurer, that must take employers the voluntary market will not, and that its own statute places outside the state government:
“the company shall provide workers' compensation and incidental employers' liability coverage to employers otherwise entitled to coverage, but not able to or not electing to purchase coverage in the voluntary insurance market”
“The company is not considered a state agency or instrumentality of the State for any purpose.”
For a drywall business, comp is placed the way the rest of the program is: in the private market, or through self-insurance the Workers’ Compensation Board oversees. Who counts as an employee when hangers and tapers are paid by the board or the job, and what certificates a subcontracted crew should hand you, are policy questions rather than Maine questions, set out on the workers’ compensation page. Nothing verified here crosses a state line, so if your crews take work in a neighboring state, the rules there are that state’s own.
Consumer protection, environment, insurance: the offices in this record
The Bureau of Insurance regulates insurance in the state. You can look up an insurance agency’s license, ours included, on NIPR.com. The other bodies this page draws on, with the role the record verified for each:
- Office of the Maine Attorney General: consumer protection; guidance on home construction contracts and on which trades the state licenses
- Office of Professional and Occupational Regulation: statewide professional and trade licensing, including electricians and plumbers (no general or drywall contractor license)
- Maine Department of Environmental Protection asbestos program: asbestos abatement licensing and certification, notification, inspections and work practices (Chapter 425)
- Maine Department of Environmental Protection: state lead program (Lead Hazard Prevention): licensing of lead inspectors, risk assessors and abatement contractors; RRP itself is EPA-administered
- Workers’ Compensation Board: workers’ compensation administration, coverage records and self-insurance oversight
The asbestos and lead programs both sit within the Maine Department of Environmental Protection, which is why its name appears twice above. No state board licenses drywall or general contracting, and there is no state workers’ compensation fund, so in an ordinary week the office that matters most is the town office where your job sits.
Metro areas on the Census map, and the town office in each
The metro areas below are every metropolitan area the U.S. Census Bureau draws around a city in Maine. Permits and the building code are handled town by town, so a crew working across one of these metros can meet a different local office in each place it works.
Portland-South Portland, ME
Maine counties in this metro: Cumberland County, Sagadahoc County and York County.
Bangor, ME
Maine counties in this metro: Penobscot County.
Lewiston-Auburn, ME
Maine counties in this metro: Androscoggin County.
As advice, keep track of which town each job sits in, inside a metro or outside one, and check that town’s permit and code questions before the bid goes out.
The policies each job leans on, from mud to lifts
The coverage that answers for the work itself is the set of policies a drywall business carries wherever it works, and each has its own page:
- General liability for injury and damage to others, including finished work and tear-out.
- Workers’ compensation for the crew, including crews paid by the piece.
- Commercial auto for the vans and trucks that carry board and mud to the job.
- Inland marine coverage for tools and equipment for the lifts, stilts, taping tools and sanders that move from job to job.
- Umbrella liability for limits above the primary liability policies, often asked for in a subcontract.
- Commercial property for the shop and what is kept in it.
A crew retaping rooms in occupied houses signs different contracts and opens different older walls than a crew hanging board on a commercial project, and the service pages take each on its own terms. When you are ready to put the pieces together for work in Maine, a quote request is the place to start.
State rules decide who may do the work and how; the policies decide who pays when something goes wrong.
- A license, registration or certification is a requirement of the state, not insurance.
A panel for Maine in rows. Each row sets a requirement of the state beside the exposure that requirement leaves open and the coverage line that answers it. Contractor license: No statewide license; a city, town or county may set its own. It leaves open injury and damage to others from the work, during the job and after it, which General Liability answers. Lead-safe renovation: The federal program runs lead-safe renovation here. It leaves open paint dust disturbed when older walls are cut, patched or sanded, which General Liability answers. Asbestos in wall and ceiling material: A state program reaches removal of this material. It leaves open disturbing older joint compound, wallboard or plaster, which General Liability answers. Workers’ compensation: Required for covered employers, bought in the open market. It leaves open a crew member hurt on the job, which Workers’ Compensation answers. Notes: A license, registration or certification is a requirement of the state, not insurance. The conclusion reads: State rules decide who may do the work and how; the policies decide who pays when something goes wrong. No figures are shown.
Nearby states we also write
Maine coverage, services and state offices
What we insure
Coverage lines
Outside authorities
Maine drywall contractor insurance questions
Is there a Maine license number we should be printing on our estimates and invoices?
No. The Office of the Maine Attorney General says general contractors and trades such as roofing and framing are not licensed or regulated in Maine, and the trades the state does license, plumbing and electrical work, do not reach wallboard or taping. What a customer can ask for instead is a written contract, your certificate of insurance and the permit, where the town requires one.
We are retaping and patching a kitchen for a homeowner. Does that job need a written contract?
It can. Maine’s home construction contract law reaches contracts to remodel or repair a residence, including nonstructural work, and requires a written contract signed by both sides once the job passes the amount the statute sets, which is quoted on this page. As advice, put every residential job in writing whatever its size, so the question never turns on the final price.
Does that contract law reach a drywall job in a store or an office?
No. The law defines a residence as a dwelling with a small number of living units, and its own words put buildings used for commercial or business purposes outside the chapter. A commercial job is governed by the contract you sign with the owner or the general contractor.
We only skim over old taped seams. Is the compound under them inside the asbestos rule?
The rule draws the line by how the compound was used. Removing joint compound that only filled nail holes and taped seams is listed among activities the rule does not reach, but joint compound used as a layered system on walls and ceilings is not exempt. Which of those a wall holds is a question for an inspection, so as advice, settle it before a crew sands, cuts or scrapes an old finish, and call the Maine Department of Environmental Protection asbestos program if you are unsure.
The job is a single-family house. Can our own crew take out the asbestos, then?
Not on that ground alone. The rule exempts single-family homes from its inspection provisions, not from licensing: the statute’s licensing duty for asbestos abatement is not limited by building type. Unless your firm and your workers hold the state license and certification, plan on a licensed abatement contractor taking out regulated material before your crew starts.
Who certifies us to sand painted walls in an older Maine house?
EPA. Maine is not an authorized state for the federal lead renovation program, so the firm and renovator certification comes from the federal agency. The Maine Department of Environmental Protection runs the state’s lead program, which licenses lead inspectors and risk assessors, and a state statute requires reasonable precautions and cleanup of paint debris on renovation work outside that licensing.
Does hiring a single taper put a sole proprietor under the comp law?
Yes. Maine’s law reaches every private employer, including an independent contractor who hires and pays employees, and the Bureau of Insurance says a sole proprietor with employees must carry the coverage for them. The coverage comes from a workers’ compensation policy or approved self-insurance; there is no state fund.
After a run of declined comp applications, where does a small drywall company turn?
A company created by statute as a mutual insurer must provide workers’ compensation and incidental employers’ liability coverage to employers that are entitled to coverage but cannot or do not buy it in the voluntary market. The statute says it is not a state agency. As advice, ask your agent to place the coverage there if the voluntary market keeps declining, rather than leaving the crew uncovered.
This page describes insurance for drywall contractors operating in this state. It is general information, not legal advice and not a statement of coverage. Licensing, lead-safe and asbestos requirements change; verify current requirements with the agency named before relying on them.
Get a quote for your Maine drywall work
Tell us which towns your crews work in, whether the jobs are homes or commercial space, how old the finishes are and who is on the payroll, and we will shape the program to fit.